BALL JOINT RIVET REMOVAL TOOL HOW TO

Now that you have everything apart, it is an excellent time to double-check your other joints. Take care while using your hammer to hit the housing. It will take some time and a bunch of different angles to get your ball joint to break loose, but you will see and hear the sound when it finally does break loose. Now you should be able to use a hammer to separate the bottom part of the joint from the top.Īlways be aware of where you are hitting. You can put a piece of wood in between your axle hub and the jack. Place your jack directly underneath your axle hub where the ball joint goes down. Now your vehicle is all lifted and held by your jack stands.įor ball joints in the lower control arm. But when using a ball joint separator, you can consider lifting your vehicle with a car lift. It is not advisable to use a car lift for this process due to the method we need to use to get this done. Now completely take-off the lug nuts of your wheels so you will be able to remove the wheels from your car. After lifting your car with your jacks, place your jack stands at strong positions under your car.Įnsure your jack stands are well placed, so the jack stands will evenly distribute your vehicle’s weight. We would show you the best and safest position to set your jack, and jack stands based on your vehicle’s model. If you are not sure about where to place the jack, inform us. Using a soft part can damage your vehicle parts. If you are using a jack, then you need to properly set your jack at a strong point in your vehicle. Give the lug nuts a quarter turn each do not completely remove it. Removing lug nuts can prove difficult, especially when they are all rusty. Take-off the axle nut and lug nuts holding your wheels the axle nut of some vehicle models is enclosed, so you might need any screwdriver types to pry the cover open. Make sure the car is resting on an even surface, and also remove any object on top of your vehicle. Always Get your mechanics toolbox close during repairs to enable you to grab the tools you need quickly. In fact, any person that does not have these should stop and not proceed at all. If you don’t own any safety wear at all, then you need to get one. Like we always say in our previous articles, this is a crucial step if you are about to perform any automobile repairs.

BALL JOINT RIVET REMOVAL TOOL HOW TO

Therefore, you need to know how to do this properly to avoid damaging other parts of your vehicle – or directly giving an impact to on your camber. It is quite technical, especially when you are not using any upper or lower ball joint removal tool. Strictly follow these steps to pull off this repair successfully. How To Remove Ball Joint Without Tool (Upper And Lower) This article will show you some ball joint removal tricks to help you replace your upper and lower ball joint without having to go to the mechanic or spend your money on buying any joint press tool. You can read our previous article on the symptoms of a bad ball joint to know when the ball joints of your vehicle are faulty. This component provides easy movement between your vehicle’s control arms and steering knuckles so you can have a smooth and safe ride, allowing you to control your vehicle’s wheels effectively. Your ball joints are essential components of the front suspension on practically every automobile manufactured. You just need some simple tools you have in your garage to help you out with this process. With this knowledge, you do not need to also stress about building a homemade ball joint press. So knowing how to remove ball joint without tool in your vehicle is one of the essential automobile DIY skills you need to acquire. This tool is used to separate the ball joint from the spindle support arm, and easy to install.ĭisclaimer: Nicecnc Store parts are not sponsored or endorsed by, or affiliated with the brands its parts fit, including Harley-Davidson，KTM, Duke，Aprilia，Triumph，Husqvarna, Honda, Yamaha, Kawasaki, Suzuki, Beta, GASGAS, Sherco, Polaris, Can-am, Arctic Cat, Ski-Doo，Piaggio, Ducati, MV Agusta, Moto Guzzi, Benelli, Buell, CF-Moto, Enfield, Hyosung, Indian,etc.It can be quite expensive to purchase a ball joint press or separator tool.The ball joint remover well designed, heavy-duty, the small size allows being carried conveniently and also easy to use.Anodizing available in red to resist wear and corrosion.CNC-machined from strong but lightweight 6061-T6 aluminium,can be used for a long time.

Ball joint rivet removal tool